Skip to main content

DIY Table Saw

Yes, I know I'm not the first person to make one of these, and I certainly won't be the last. When I started making the banjo block rim the other week, I quickly realised that it would have been a whole lot easier if the wood was at least a little bit square to start with, so I figured that before I made any more it would be nice to have a table saw to square up the source material. Naturally I didn't really want to go out and buy one if I was only going to use it every blue moon so I decided to put my old circular saw and some scrap wood to good use and build my own.

The picture below show the finished article, complete with fence. The stand is from a broken old workmate-a-like I had lying around, the top is from some kitchen cabinet material as is the fence. I added a safety NVR switch, because it's dangerous enough as it is, and I didn't want to add further risks.

Anyway, enough of that, here are the pictures

DIY table saw

circular saw mounting

Comments

Popular posts from this blog

Vox Pathfinder 10 and Pathfinder 15 Simulation

I've got a Vox Pathfinder 10 amplifier that I bought a couple of years ago, and I love it. It's a great little amplifier, but I don't care for the distortion channel, it just sounds harsh to my ears. There are quite simple modifications that can be done to this amplifier to remove the clipping LED's and increase the boost of the clean channel (check out Ben Craven's mods  for details). I'd been considering doing some of these, but whilst researching the subject, I discovered that the currently out of production (as at Nov '18)  Pathfinder 15/15R generally receives a lot more love than the Pathfinder 10. I found schematics for both the PF15 and the PF15R online, and saw that there were a lot of similarities between the PF10 and the PF15, particularly the earlier non-reverb PF15. The PF15R (with reverb) is quite a bit different after the first two opamp stages. I thought I'd model both the PF10 and PF15 pre-amp stages in LTspice  to see how they compar...

Vox Pathfinder 15 Tremolo Repair

Last year, I snapped up a Vox Pathfinder 15 (non-reverb) combo amplifier from ebay. The seller was a charity shop, and the amplifier was listed as "untested", so I was taking a bit of a gamble, but figured I'd have a good chance of being able to fix it it it wasn't working, and cosmetically, it looked almost mint. When it arrived, I plugged it in, and as you guessed, it was not working. Barely any sound, and what sound there was was horribly distorted. One thin I did notice was the the power on LED was not aligned correctly with the hole in the back panel, so I did quickly took it apart, and realigned the potentiometers and LED indicator, but didn't have a look in detail at the circuit. I put it back together, but the problem remained. My guess was that the problem was the famous "cambridgitis" (just google that term and you'll find all about it). Basically, a problem where the optocoupler that controls the tremolo circuit fails. A common failure...

Marshall Lead 12 Preamp Simulation

Having already modelled the preamp stage of the  Vox Pathfinder 10, 15 and 15R  respectively, and noted the similarities circuit-wise between the PF10 and the PF15, I discovered another much-loved practice amp with a similar preamp stage - the Marshall Lead 12. I should say, before going any further, that there are huge differences between the power amp stages. The PF10 uses a TDA2030A chip amp whereas the Lead 12 uses discrete components. The chip amp power stage on the PF10 shouldn't colour the tone much, but the discrete one in the Lead 12 most likely does contribute to the overall tone of the amplifier. A simulation of the preamp stage with the Treble, Bass and Mid controls at 50% and the Gain control at 0%-100% gave this Marshall Lead 12 Preamp Simulation Marshall Lead 12 preamp simulation, Gain 0%-100%, TMB @ 50% Vox Pathfinder 10 preamp simulation (overdrive engaged) Vov Pathfinder 10 preamp simulation, Gain 0%-100%, T+B @ 50% Comparing the two, ...